 |
 |
 |
TEXTURED HDPE GEOMEMBRANE
ENGLISH UNITS
HDPE ENGLISH UNITS
|
| |
Minimum Average
Values |
| Property |
Test Method |
40 Mil |
60 Mil |
80 Mil |
100 Mil |
|
| Thickness, mils |
ASTM D 5994 |
|
|
|
|
| minimum average |
|
38 |
57 |
76 |
95 |
| lowest individual of 8 of 10 readings |
36 |
54 |
72 |
90 |
| lowest individual of 10 readings |
34 |
51 |
68 |
85 |
|
| Asperity Height, mils |
ASTM D 7466 |
10 |
10 |
10 |
10 |
|
| Sheet Density, g/cc |
ASTM D 1505/D 792 |
0.940 |
0.940 |
0.940 |
0.940 |
|
| Tensile Properties
1 |
ASTM D 6693
|
|
|
|
|
| 1. Yield Strength, lb/ in |
|
84 |
126 |
168 |
210 |
| 2. Break Strength, lb/ in |
|
60 |
90 |
120 |
150 |
| 3. Yield Elongation, % |
|
12 |
12 |
12 |
12 |
| 4. Break Elongation, % |
|
100 |
100 |
100 |
100 |
|
| Tear Resistance, lb |
ASTM D 1004 |
28 |
42 |
56 |
70 |
|
| Puncture Resistance, lb |
ASTM D 4833 |
60 |
90 |
120 |
150 |
|
| Stress Crack Resistance
2, hrs |
ASTM D 5397 (App.) |
300 |
300 |
300 |
300 |
|
| Carbon Black Content
3, % |
ASTM D 1603 |
2.0 - 3.0 |
2.0 - 3.0 |
2.0 - 3.0 |
2.0 - 3.0 |
|
| Carbon Black Dispersion
4 |
ASTM D 5596 |
|
-Note 4- |
|
|
| Oxidate Induction Time (OIT) |
|
|
|
|
|
| Standard OIT, minutes |
ASTM D 3895 |
100 |
100 |
100 |
100 |
|
| Oven Aging at 85°C |
ASTM D 5721 |
|
|
|
|
High Pressure OIT
(% retained after 90 days) |
ASTM D 5885 |
80 |
80 |
80 |
80 |
|
| UV Resistance
5 |
ASTM D 7238 |
|
|
|
|
High Pressure OIT
6
(% retained after 1600 hrs) |
ASTM D 5885 |
50 |
50 |
50 |
50 |
|
| Roll Dimensions |
|
|
|
|
|
| 1. Width (feet): |
|
23 |
23 |
23 |
23 |
| 2. Length (feet) |
|
750 |
500 |
375 |
300 |
| 3. Area (square feet): |
|
17,250 |
11,500 |
8,625 |
6,900 |
| 4. Gross Weight (pounds, approx.) |
3,500 |
3,500 |
3,470 |
3,470 |
|
|
1. Machine direction (MD) and cross machine direction (XMD) average values should be on the basis of 5 test specimens each
direction. Yield elongation is calculated using a gauge length of 1.3 inches; Break elongation is calculated using a gauge
length of 2.0 inches.
2. The yield stress used to calculate the applied load for the SP-NCTL test should be the mean value via MQC testing.
3. Other methods such as ASTM D 4218 or microwave methods are acceptable if an appropriate correlation can be established.
4. Carbon black dispersion for 10 different views: 9 in Categories 1 and 2 with one allowed in category 3.
5. The condition of the test should be 20 hr. UV cycle at 75°C followed by 4 hr. condensation 60°C.
6. UV resistance is based on percent retained value regardless of the original HP-OIT value.
This data is provided for informational purposes only and is not intended as a warranty or guarantee. Poly-America assumes no responsibility in connection with the use of this data. These values are subject to change without notice. REV. 08/11
|
|
|
|
|
 |
|
|
|
|
|
